Skip to main content 
Regent Hardware Panic Hardware & Exit Devices
Aluminum storefront concealed vertical rod, rim, and mortise exit devices. Authorized service for the Regent 5770 CVR, 5750 Rim, 5760 Mortise, and EL5770 electrified series across Brevard County.
About Regent Hardware (Regent Hardware (independent manufacturer))
Regent Hardware is an independent commercial hardware manufacturer specializing in aluminum storefront exit devices — purpose-built for the narrow-stile storefront doors common on Florida commercial buildings, retail, and strip-center properties. Their flagship 5770 Series concealed vertical rod (CVR) exit device is a direct alternative to Jackson 10 Series CVR, Dor-O-Matic 1990, and Adams Rite 8000 Series on aluminum storefront applications.
Important disambiguation: this is Regent Hardware (regenthardware.com), the commercial storefront exit device manufacturer. It is not the Schlage Regent series, which is a separate residential knob and lever lineup — different product, different market.
Key-En-Lock services the full Regent Hardware product line across Brevard County. We source Regent parts through established distributors (Door Controls USA, DK Hardware, County Locksmith) and stock the most common service items — dogging kits, end caps, bar sets — for same-visit repairs on 5770 Series CVR devices. For customers with aging Regent hardware, we can convert mechanical 5770 devices to electric latch retraction using the retrofit bottom rail kit, avoiding full device replacement in most cases.
Regent Hardware Product Lines We Service
| Model / Series | Description | Typical Use |
|---|---|---|
| Regent 5770 Series CVR | Concealed vertical rod exit device for aluminum storefront impact doors. Flagship Regent product. Available 36", 42", 48" door widths. | Aluminum storefront (CVR) |
| Regent 5770 MDR-ELR | Electrified 5770 with Motor-Drive Latch Retraction (EL5770). 24VDC @ 1 Amp. Ties directly into access control for credentialed entry. | Access-controlled storefronts |
| Regent 5770 MDR-ELR-RX | 5770 electrified variant with Request-to-Exit switch — integrates with access control for egress logging and door-contact bypass. | Full access control integration |
| Regent 5750 Series Rim | Rim-type narrow-stile exit device. Alternative to 5770 CVR when concealed rods aren't needed. Available 36", 42", 48" door widths. | Single-door storefront panic |
| Regent 5760 Series Mortise | Mortise exit device for premium narrow-stile applications where flush appearance and mortise security matter. | Premium storefront mortise |
| Regent EL5770 Retrofit Rail | Replacement bottom rail with integrated 24VDC latch retraction motor — converts existing mechanical 5770 to electrified without full device swap. | Electrification retrofits |
| Regent Overhead Concealed Closer | Overhead concealed door closer for aluminum storefront headers — competes with Jackson 20/30/40 and Dor-O-Matic OHCC. | Aluminum storefront headers |
| Regent Surface Closer | Surface-mounted door closer for aluminum and hollow-metal doors. | Commercial closer retrofits |
| Regent Pivots & Hinges | Offset pivots, continuous hinges, and intermediate pivots for aluminum storefront doors. | Storefront door hang hardware |
| Regent Locks & Cylinders | Mortise cylinders and lock bodies that pair with 5770/5750/5760 exit devices and storefront deadbolts. | Storefront cylinder service |
Available Trims & Lever Options
The trim is the outside hardware attached to the exit device — the lever, pull, thumbpiece, or knob that determines how the door opens from the outside when unlocked. Inside remains the panic bar (for code-compliant free egress). Below are the standard trim options available for Regent Hardware exit devices:
| Trim Code | Type | Function | Description |
|---|---|---|---|
| Exit only | Exit only (no outside trim) | Emergency egress only | Most common 5770 configuration. No exterior hardware — the device is purely for code-compliant egress. Entry on the adjacent leaf via deadbolt/deadlatch. |
| Mortise cyl block | Exterior mortise cylinder | Key retracts latch | Exterior mortise cylinder block paired with the 5770/5750 chassis — key turn retracts the latch for entry. Sold separately from the chassis. |
| Pull trim | Architectural pull | Pair with mortise cylinder | Aluminum pull handle for exterior — used in combination with the mortise cylinder block for key-retract-latch entry. |
| Ladder pull | Ladder-style pull | Aesthetic + cylinder entry | Vertical ladder pull common on modern commercial storefronts — paired with mortise cylinder for key entry. |
| DT | Dummy trim | Aesthetic only | Matching dummy pull for the inactive leaf of a pair — no function. |
| RX switch | Request-to-Exit switch | Access control integration | Built-in REX switch on the MDR-ELR-RX variant — signals access control on bar push for egress logging and door-contact bypass. |
Available Finishes
Finishes are specified using ANSI/BHMA finish codes. The most common finishes for commercial door hardware in Florida are satin chrome (626), satin stainless (630), and oil-rubbed bronze (613). Most trims can be ordered in any of these finishes:
Common Regent Hardware Repairs
- 5770 CVR push bar sticking or slow return — bar spring wear or chassis debris. On-site rebuild with standard bar set (57-36CL-BAR-SET or 57-36D-BAR-SET).
- Top or bottom latch not engaging — vertical rod adjustment or extension rod service. Regent stocks extension kits (57-EXTKIT, 57-EXTROD36) for field adjustment.
- Dogging hex key spins but doesn't hold bar retracted — failed dogging mechanism. Direct replacement with Regent 5770 dogging kit (5770-dg-kit), about 30-minute repair.
- End cap damaged or missing — OEM replacement. Hinge-side end cap (SA11677) carries the UL Listed 14KJ designation; stile-side end caps (57-EC1, 57-EC2) are separate SKUs.
- EL5770 motor not retracting on credential — check 24VDC @ 1A power supply first (most common cause), then motor module, then wiring through the hinge transfer.
- EL5770 REX switch not signaling access control — RX switch or wiring fault. Diagnosis + switch replacement.
- Mechanical 5770 needs access control upgrade — retrofit the bottom rail with the EL5770 replacement rail rather than replacing the whole device. Swap takes ~30 minutes: two end caps off, four screws, new rail in, reinstall.
- Device handed wrong — 5770 chassis can be rehanded in the field; we handle re-handing without replacement.
Electrification & Access Control Integration
Adding electric latch retraction (EL) or other electrification options turns mechanical Regent Hardware devices into access-control-capable entrances. Exit remains code-compliant free egress from the inside, but outside entry becomes scheduled, credentialed, or automated. See our full electrification overview on the main panic hardware page.
- 5770 MDR-ELR (EL5770) — Motor-Drive Electric Latch Retraction. Factory-electrified 5770 with a 24VDC motor in the bottom rail that retracts the latch on signal from access control.
- 5770 MDR-ELR-RX — Same as above plus integrated Request-to-Exit switch for full access control integration (credential authentication, egress logging, door-contact bypass).
- EL5770 Retrofit Rail — Replacement bottom rail with the motor preinstalled. Converts an existing mechanical 5770 to electrified in about 30 minutes without full device replacement. Requires a 24VDC @ 1A power supply (sold separately) and a power transfer hinge or armored door cord.
- Power supply requirements — 24VDC @ 1A minimum. We specify and install UL-listed power supplies from established manufacturers (Altronix, Seco-Larm) rather than letting the access control integrator under-spec the power side.
- Integration with PDK.io — EL5770 works cleanly with PDK.io cloud access control and traditional card/keypad systems. We wire the full loop including power, control relay, REX, and door-position contact.
- Fire alarm release — Electrified Regent devices can be wired for release on fire alarm activation per NFPA 101. Required on certain egress doors in Florida commercial occupancies.
Regent Hardware FAQ
Is Regent Hardware the same as Schlage Regent?
No — completely different products. Regent Hardware (regenthardware.com) is an independent commercial manufacturer of aluminum storefront exit devices, closers, hinges, and pivots. The 5770 concealed vertical rod device is their flagship product. Schlage Regent is a separate residential knob and lever lineup from Schlage (Allegion) sold through home improvement channels — different market, different product, different use case. This page is about commercial Regent Hardware storefront exit devices.
How does Regent 5770 compare to Jackson 10 Series CVR or Adams Rite 8000?
All three are narrow-stile concealed vertical rod exit devices for aluminum storefront doors. Functionally they solve the same problem — panic egress on aluminum double-door pairs with a clean appearance (no surface-mounted rods). Differences come down to parts availability, electrification path, finish match, and price. Jackson and Adams Rite benefit from ASSA ABLOY distribution. Regent ships through independent distributors and is often priced below the ASSA ABLOY brands for equivalent specification. For replacement on existing Regent-equipped buildings, stay with Regent — dimensional compatibility is cleanest.
Can I electrify my existing Regent 5770 without replacing the whole device?
Yes — this is the cleanest retrofit path in the Regent lineup. The EL5770 retrofit rail replaces your existing bottom rail and includes a factory-installed 24VDC motor for latch retraction. Installation is about 30 minutes: remove the two end caps, unscrew the four rail mounting screws, swap rails, reinstall. You'll also need a 24VDC @ 1A power supply and a power transfer hinge or armored door cord (we specify and install both). The chassis, push bar, and vertical rods all stay in place.
What finishes does Regent come in?
Two standard aluminum storefront finishes: CL (Clear anodized aluminum) — BHMA 628 equivalent, the most common commercial storefront finish; and D (Dark Bronze / Duronotic) — BHMA 710 equivalent, common on bronze-tone aluminum storefronts. Stock 36" devices ship in either finish from the manufacturer; 48" and other non-stock sizes may take up to 2 weeks.
Do you stock Regent parts for emergency repairs?
We carry the most common service items on the truck — 5770 dogging kits, end caps, bar sets — for same-visit repairs. Less common items (extension rod kits, full rail assemblies, electrified components) are sourced through our distributor network with typical 1–3 business-day lead times. For emergency door-won't-latch situations, we can often field-repair the 5770 mechanism without waiting for parts.
Is Regent fire-rated?
The UL Listed 14KJ designation on Regent 5770 end caps refers to UL material listings, not a blanket fire rating for the full device. For fire-rated storefront applications in Florida, we verify the specific model's UL fire rating with the manufacturer before installation — don't assume. If fire rating is required and the Regent variant you need isn't available fire-rated, we'll spec a Von Duprin 33A-F or Jackson fire-rated alternative that will fit the same door opening.
Will Regent work on impact-rated aluminum storefront doors common in Florida?
Yes — Regent 5770 is explicitly marketed for aluminum storefront impact applications, which matters for Florida Building Code compliance in coastal and high-velocity hurricane zones. The narrow-stile chassis is dimensionally compatible with most impact-rated aluminum frames (Kawneer, YKK AP, EFCO, Arcadia). For new installs on impact-rated doors, we verify frame compatibility before ordering.
Related Panic Hardware Brands
Explore More Commercial Hardware
Key-En-Lock services the full commercial hardware lifecycle across Brevard County. Beyond panic hardware, we maintain parallel authority coverage for door closers, electric strikes, and the full commercial locksmith service range.