Skip to main content 
Kwikset SmartCode Programming Instructions
Add, change, and delete user codes on Kwikset SmartCode electronic deadbolts and keypad locks.
SmartCode 910
SmartCode 913
SmartCode 914
SmartCode 915
SmartCode 917
SmartCode 955
SmartCode 260
About Kwikset SmartCode Locks
Kwikset SmartCode electronic deadbolts and lever locks provide keyless entry with programmable user codes. These locks support up to 30 user codes (16 on older models) and feature SmartKey re-key technology. The programming process is the same across most SmartCode models.
| Compatible Models | SmartCode 909, 910, 913, 914, 915, 917, 955, 260 |
| Code Length | 4 to 8 digits |
| Max User Codes | Up to 30 (model dependent) |
| Power | 4 AA batteries |
| Default Master Code | None (uses Program button) |
Add a User Code (Mastercode Disabled)
Steps to Add a User Code
- Make sure the door is open.
- Press the Program button once on the interior side of the lock (use a paperclip or SmartKey tool).
- Press the Checkmark (✓) symbol once.
- Enter a new user code (4-8 digits).
- Press the Lock symbol once.
Add a User Code (Mastercode Enabled)
Steps to Add a User Code with Mastercode
- Keep the door open.
- Press the Program button once. Checkmark flashes 5 times with 5 beeps.
- Press the Checkmark (✓) symbol once.
- Enter your Mastercode.
- Press the Lock symbol once.
- Enter the new user code.
- Press the Lock symbol once.
Delete All User Codes (Mastercode Enabled)
Steps to Delete All User Codes
- Keep the door open.
- Press the Program button once. Keypad flashes green with 3 beeps.
- Press the Lock button once.
- Enter your Mastercode.
- Press the Lock button once.
- Press 9 six times.
- Press the Lock button once.
- Press 9 six times again.
- Press the Lock button once.
Enable/Add a Programming Code
Steps to Set a Programming Code
- Make sure the door is open.
- Press and release the Program button. Two beeps will sound.
- Press 3. One short beep, keypad flashes green.
- Press the Kwikset button.
- Enter your desired Programming Code (4-8 digits).
- Press the Kwikset button.
- Re-enter the Programming Code.
- Press the Kwikset button.
Factory Reset
⚠️ Factory Reset — Erases ALL Codes
- Remove the battery pack.
- Press and hold the Program button while reinserting the battery pack.
- Release the button once the battery pack is installed.
- The status LED will flash red and green.
- Press the Program button once more.
- The latch bolt will extend and retract to re-learn the door orientation.
Manufacturer Documents
📄 Official Kwikset Support & Manuals
Troubleshooting
- Keypad not responding: Replace batteries with fresh Duracell or Energizer AA alkaline batteries.
- Lock not locking/unlocking: Perform the door handing process — remove batteries, hold Program button while reinserting, then press Program again.
- Beeps but won't unlock: Verify you're entering the correct code. After multiple failed attempts, the lock may enter lockout mode — wait 60 seconds.
- Code rejected: The first 4 digits of each user code must be unique across all stored codes.
Frequently Asked Questions
What is the default Mastercode on a Kwikset SmartCode lock?
The factory default Mastercode (Programming Code) is typically not pre-set on newer models — you create one during initial setup. On older models, the default may be found on a sticker on the back of the lock interior. Check the installation guide that came with your lock for the specific default.
How many user codes can a Kwikset SmartCode lock store?
Most current SmartCode models (913, 914, 915, 917, 955) support up to 30 user codes. Older models may support 16 codes. Each code must be 4-8 digits long, and the first 4 digits of each code must be unique.
Can I program a Kwikset SmartCode lock without the Programming Code?
No. The Programming Code (Mastercode) is required to add, delete, or modify user codes. If you've lost the Programming Code, you'll need to perform a factory reset, which erases all existing codes and settings. The Programming Code sticker is usually located on the back of the interior assembly.
Will I lose my codes if I change the batteries?
No. All programmed codes are stored in non-volatile memory and survive battery changes. Simply replace the 4 AA batteries and your codes will still work. You do not need to reprogram anything after a battery swap.
What do I do if I'm locked out of my Kwikset SmartCode?
If you've forgotten all user codes, you can still use the physical key to unlock the door. If you've also lost the key, contact a licensed locksmith. A factory reset will restore default settings but requires physical access to the interior of the lock.
Need More Help?
If these instructions didn't solve your issue, contact the manufacturer directly or call your local locksmith:
Can't reach the manufacturer? Our licensed locksmiths service all Kwikset models throughout Brevard County.